Stair Klad Oak Stair Cladding Tread 1500mm

Brand: Unbranded 100% Positive reviews



Need something specific or  ordering in bulk?


Stair Klad Engineered Oak Tread 1500mm

Oak Stair Cladding for your Stairs

Oak Stair Klad 1500mm Treads are used with the Oak Stair Klad Risers, the treads are designed to push down onto the riser during installation

Use 1000mm Treads for all standard steps up to 1000mm wide, for steps wider than 1000mm or winder steps use 1500mm. Simply cut your treads and risers to size and glue into position using polymer adhesive.

All Stair Klad Stair Cladding products are supplied lacquered in a clear satin finish

Cheshire Mouldings Oak Stair Klad System is the perfect way to clad and create the warm and inviting look of an oak staircase without the expense and trouble of replacing your existing staircase. 

Stair Klad 1500mm Tread and Riser Usage

1500mm Treads and risers are used to clad your existing steps and riser boards that are over 1000mm wide. If your existing step is deeper than 300mm the you will need to use the extension boards.

We suggest you measure the width of your steps and buy the 1500mm treads and risers only if your step is wider than 1000mm. When cladding a winder step you may find that they are deeper than the 300mm Stair Klad Tread, all you need to do in this instance is purchase a tongue and groove Klad extension board that connects to the back of the pre-grooved tread, extending it to the full width of your existing winder step. 

Stair Klad Stair Cladding Fitting Guide

Before you start your stair cladding installation please read the instructions fully and contact us if you have any queries.

  1. Before you start, ensure that your existing steps and riser boards are clean, dry and free from uneven defects. We suggest you thoroughly sand the steps to ensure you get a good sound base for your new Stair Klad Treads and Risers
  2. Measure the existing bullnose protrusion from the face of the existing riser board to the furthest point of the bullnose on the existing step. You can then cut packing strips from timber that will push the bottom of the Stair Klad Riser board out and in line with the end of your bullnose. We suggest that these packing strips are screwed into place for stability.
  3. Starting at the Top of the staircase, measure and cut three Stair Klad Risers to size and glue them onto the packing strips using
  4. Measure the depth and width and cut a Stair Klad Tread to size. Apply a 10mm bead of Flexible Polymer Adhesive to the top of your existing step
  5. Press the Stair Klad Tread onto the Adhesive firmly ensuring the Stair Klad Riser fits securely into the groove on the bottom of the Stair Klad Tread
  6. Continue down the stairs fitting 3 riser boards first and then the treads.
  7. If you reach a mid-landing, then use the same method above but use Klad Extension Boards to cover the landing area. These are supplied with a tongue and groove on the long edges that slot into the back edge of the tread.
  8. If you have large Kite Winder Steps, then you may need to use the 1500mm wide Stair Klad Treads and Risers with Stair Klad Extension Boards. You can usually use 1000mm Treads and Risers with Extension Boards for triangular shaped winders no wider than 1000mm
  9. Fix the stair Klad treads and any joining riser boards first then cut the extension boards to size, apply a good amount of polymer adhesive and push the boards together until the area is covered. Do not put adhesive between the T&G joints.
  10. Work your way down the stairs to the bottom floor or use the Stair Klad Bottom Bullnose Step for cladding bullnose steps

You can download the Cheshire Mouldings StairKlad Instructions manual from here


We deliver to UK Mainland only. We charge £10 shipping for orders up to £150. Orders over this have a flat fee of £15. However, our couriers do deliver to most offshore locations but charge a premium which unfortunately we have to pass on. Contact us for prices to Isle of Wight, Scottish Isles, Northern Ireland and Channel Isles etc.


We wrap and pack your order to ensure the product reaches you in the condition it left us, however, occasionally transport damages do occur. On the day of your delivery please check all products are present and in good condition.

Should you decide to return the products you must notify us of the refund within 14 Working Days of receipt of the goods. You have a further 14 days to return the goods to us.

Deliveries are made using a 3rd party carrier, due to the weight and length of our product we cannot give timed deliveries, however, we can specify a suitable day when you can be available to accept and sign for your order. Our 3rd party carrier does not give pre-delivery calls prior to the delivery, it is an all day delivery slot.

Deliveries are made using a 3rd party carrier on pre-arranged delivery days where possible. Delivery times shown on Go Banana are estimated, if we have not contacted you to arrange a specific delivery day then please email us to confirm. A note of the delivery day will be found on the sales invoice - If we haven't emailed please check there.

You will need to be available to help unload and sign for your order. When you sign for your order you are accepting that the goods are all present and received in good condition.

We advise that all customers:

1) Check you are signing for the correct number of parcels

2) Check all parcels are addressed to you

3) Check that all parcels are undamaged - if there are any signs of damage to any of the parcels ensure you sign and write "damaged" on the delivery slip

4) Open all parcels on the day of delivery to check all products have been received in good order and complete

5) Contact us on the day of delivery if there are any issues with your order

6) Blueprint Joinery will replace any damaged products on a next working day service.

IMPORTANT: If the above is not acceptable to you then we can pick and pack your order ready for you to collect or send in your own transport. Please do not buy our product if you do not accept the above delivery statements.